Ad blocker detected : Our website is made possible by displaying online advertisements to our visitors. Please consider supporting us by disabling your ad blocker on our website.
Aller à la recherche avancée
Hello again, I think I found a solution for my problem, but not the cause. If I start Jedicut from the start menu (not a double click on a jdc-file) , go to tool and do nothing but hit "cancel", I can load any jdc-file and run the cutting process. So I think it may have something to do wit...
- Forum : Jedicut - English board
- Sujet : Runtime error
- Réponses : 4
- Vues : 5173
- ven. juin 29, 2012 5:26 pm
- Aller au message
Hello, I wil try it, but why can I use the manual mode and the maschine works without problems? If it is a problem with the driver of my express card, it should not work in the manual mode either!? But I noticed that If I load a jdc-File like the one attached in the first post, I get problems in the...
- Forum : Jedicut - English board
- Sujet : Runtime error
- Réponses : 4
- Vues : 5173
- ven. juin 29, 2012 2:32 pm
- Aller au message
Good evening, I am sorry to ask for your help again. In 9 out of 10 times, I get a runtime error when i try to start the cut. After confirming error 1 (see attached file), the second one pops up. After that jedicut crashes and I have to restart it again. I can use the manual mode and in some cases i...
- Forum : Jedicut - English board
- Sujet : Runtime error
- Réponses : 4
- Vues : 5173
- jeu. juin 28, 2012 11:05 pm
- Aller au message
Hallo Manfred, vielen Dank für deine schnellen antworten. Ich habe selber auch noch ne Lösung für das Stottern der Motoren gefunden. Unter Punkt 11 ist zu lesen, dass als Vorschub Werte zwischen 500000 und 2000000 bei Verwendung der Steuerkarte von Letmathe zu verwenden ist. http://www.rc-letmath...
- Forum : Jedicut - English board
- Sujet : Cutting speed
- Réponses : 5
- Vues : 5522
- lun. juin 25, 2012 10:55 pm
- Aller au message
Hallo Manfred, vielen dank für die Antowort. Leider ist es bei mir so , dass wenn ich Vollschritt oder Halbschritt fahre, dann haben die motor immer wieder aussetzer und bleiben brummend stehen. Woran das liegt weiß ich auch nicht. Des wegen bin ich auch auf 1/8 runtergegangen damit ich überhaupt...
- Forum : Jedicut - English board
- Sujet : Cutting speed
- Réponses : 5
- Vues : 5522
- lun. juin 25, 2012 7:10 pm
- Aller au message
Hello everybody, I am using jedicut with the controler board from Letmathe CNC. I have problems with the cut speed and the fast speed. Just to get the settings right, the values in the controller setting is the time between to steps. So for small values the stepper should go fast, and for big values...
- Forum : Jedicut - English board
- Sujet : Cutting speed
- Réponses : 5
- Vues : 5522
- dim. juin 24, 2012 11:32 pm
- Aller au message
Hi again,
if I see it correct you have a second user in Germany.
Once again thank you very much for all the work you put into this software.
When my CNC foam Cutter maschine is ready, I will post some picture...
Josef
- Forum : Jedicut - English board
- Sujet : Cutting fuselage from dxf
- Réponses : 12
- Vues : 9472
- mer. mai 09, 2012 11:17 pm
- Aller au message
Hello everybody,
sorry for my late responce, but I was very busy the last two days.
I had a look at your jdc file Jerome and it looks perfect. I can live with the "reverse" of dxf-file.
Thank you very much for your help and for this great piece of software
Regards,
Josef
- Forum : Jedicut - English board
- Sujet : Cutting fuselage from dxf
- Réponses : 12
- Vues : 9472
- mar. mai 08, 2012 10:46 pm
- Aller au message
Hello again, I have a dxf file for each half. Since each half contains a flute I have to separate them in the dxf file. Otherwise the two parts wounld not fit hence the wire eats up a certain amount of material. As mentioned above I can cut the parts separately but for better accuracy I like to do i...
- Forum : Jedicut - English board
- Sujet : Cutting fuselage from dxf
- Réponses : 12
- Vues : 9472
- lun. mai 07, 2012 9:53 am
- Aller au message
Hello, if I check the reverse option, the direction is changed in both the root and the tip wing panel. Therefore the result is the same. I can´t reverse the pathes for the root and the tip independently... Maybe I must be a little bit more clear. If you take a look at the root wing, the path for t...
- Forum : Jedicut - English board
- Sujet : Cutting fuselage from dxf
- Réponses : 12
- Vues : 9472
- dim. mai 06, 2012 10:14 pm
- Aller au message
Aller à la recherche avancée