Ad blocker detected : Our website is made possible by displaying online advertisements to our visitors. Please consider supporting us by disabling your ad blocker on our website.
Aller à la recherche avancée
Allways check "Cutting Wizard" before cutting!
Wire radiation you can account in "Skin property". In your example 0,5 mm (30-29/2).
- Forum : Jedicut - English board
- Sujet : CUT Problem
- Réponses : 6
- Vues : 7144
- jeu. juin 05, 2014 3:39 pm
- Aller au message
Hello!
I like this idea.(tu)
Currently Jedicut goes inversely than Complexes.
Clockwise in Complexes - anticlockwise in Jedicut.
It would be great to sync "the clocks".
- Forum : Jedicut - English board
- Sujet : CPX file type
- Réponses : 15
- Vues : 13211
- mar. mars 04, 2014 11:19 am
- Aller au message
[quote=Jerome] Jedicut should open profiles corresponding to "Emplature" and "Saumon" part, nothing else ? Is it right ? It's more easy to do that than convert CPX to JDC. :S[/quote] I did not want to admit that I do not understand what it means "Emplature" and "Sa...
- Forum : Jedicut - English board
- Sujet : CPX file type
- Réponses : 15
- Vues : 13211
- jeu. févr. 27, 2014 2:35 pm
- Aller au message
[quote=Jerome]
Do you try to move foam to the extrem left of the table, near motors (or to the extrem right) ?[/quote]
Yes, this is the best thing I can do. But it is bit too little.
- Forum : Jedicut - English board
- Sujet : Cut speed
- Réponses : 5
- Vues : 5390
- mer. févr. 26, 2014 8:26 pm
- Aller au message
[quote=Jerome] It's more easy to do that than convert CPX to JDC. :S[/quote] Life is not easy.:)-D I have problem with profiles where tip and root are diferent or have different chords. Cutting wizzard does strange cutting lines sometimes. In Complexes I can set start point and equal number of point...
- Forum : Jedicut - English board
- Sujet : CPX file type
- Réponses : 15
- Vues : 13211
- mer. févr. 26, 2014 8:20 pm
- Aller au message
Hi Jerome My question was half-baked. I want to make sure, your algorithm uses max cut speed on the side where is more steps to do. Eg. Jedicut sends sequentialy 10 steps on X1 side and 1 step on X2 side - max speed on X1 side and 10% on X2 side. In addition I have a little problem with Cut wizzard....
- Forum : Jedicut - English board
- Sujet : Cut speed
- Réponses : 5
- Vues : 5390
- dim. févr. 16, 2014 1:57 pm
- Aller au message
[quote=Jerome]
The main difficulty is to find time to do it...[/quote]
I uderstand you.
[quote=Jerome]
Are you also interested by this plugin ?[/quote]
Yes, I have problem with more complex shapes.
- Forum : Jedicut - English board
- Sujet : CPX file type
- Réponses : 15
- Vues : 13211
- sam. févr. 15, 2014 2:37 pm
- Aller au message
Hi Jerome
I set cut speed but I don't know for what point of wire it is calculated: X1, Root, Tip, X2 or another.
It is important when root and tip chord are significantly different.
Can you explain the problem?
- Forum : Jedicut - English board
- Sujet : Cut speed
- Réponses : 5
- Vues : 5390
- jeu. févr. 06, 2014 5:45 pm
- Aller au message
Aller à la recherche avancée