This is a pdf manual for my board Mabe that can help.
http://www.cnc-in.cn/pdf/4%20Axis%20CNC ... 0board.pdf
Re: Motors resonating
12Daniel,
This documentation doesn't show the signal the software need to send... What Jedicut's dll do you try ?
This documentation doesn't show the signal the software need to send... What Jedicut's dll do you try ?
Jerome
Re: Motors resonating
13I have used visualcncxp dll (It is the only dll that makes the motors go the correct distance.)
The cncboard works verry god with mach 3.
Do you know what signals thaht is putting out.
The cncboard works verry god with mach 3.
Do you know what signals thaht is putting out.
Re: Motors resonating
14There is many ways to send signals on parallel port and if I don't know what signal Jedicut need to send, I can't do anything... Do you try MaxCom_XP.dll ?
Jerome
Re: Motors resonating
15Hi again.
I tried MaxCom_XP.dll
But the scale did not match my innput .And the speed figures did not make sense.
I tried many different combinations. But the motors was worse than with visual xp (there the scale was right)
I have read and tested some more .And jused a parrallelport monitor.
And as far as I can understand :
My driverboard needs the folloving signals.
X axis one direction = constant activ low on pin 3 and step pulses (activ low )on pin 2
the oter direction = no signal on pin 3 and step pulses (activ low )on pin 2
Y axis one direction = constant activ low on pin 5 and step pulses (activ low )on pin 4
Z axis one direction = constant activ low on pin 7 and step pulses (activ low )on pin 6
A axis one direction = constant activ low on pin 9 and step pulses (activ low )on pin 8
Do this make sence ??
I hope so
I tried MaxCom_XP.dll
But the scale did not match my innput .And the speed figures did not make sense.
I tried many different combinations. But the motors was worse than with visual xp (there the scale was right)
I have read and tested some more .And jused a parrallelport monitor.
And as far as I can understand :
My driverboard needs the folloving signals.
X axis one direction = constant activ low on pin 3 and step pulses (activ low )on pin 2
the oter direction = no signal on pin 3 and step pulses (activ low )on pin 2
Y axis one direction = constant activ low on pin 5 and step pulses (activ low )on pin 4
Z axis one direction = constant activ low on pin 7 and step pulses (activ low )on pin 6
A axis one direction = constant activ low on pin 9 and step pulses (activ low )on pin 8
Do this make sence ??
I hope so
Re: Motors resonating
16My last post came out wrong.
I misunderstood the Usermanual for the board .
My driverboard needs the folloving signals.
X axis one direction = constant activ high on pin 3 and step pulses (activ high )on pin 2
the oter direction = no signal on pin 3 and step pulses (activ high)on pin 2
Y axis one direction = constant activ high on pin 5 and step pulses (activ high)on pin 4
the oter direction = no signal on pin 5 and step pulses (activ high)on pin 4
Z axis one direction = constant activ high on pin 7 and step pulses (activ high )on pin 6
the oter direction = no signal on pin 7 and step pulses (activ high)on pin 6
A axis one direction = constant activ high on pin 9 and step pulses (activ high )on pin 8
the oter direction = no signal on pin 9 and step pulses (activ high)on pin 8
Sorry
I misunderstood the Usermanual for the board .
My driverboard needs the folloving signals.
X axis one direction = constant activ high on pin 3 and step pulses (activ high )on pin 2
the oter direction = no signal on pin 3 and step pulses (activ high)on pin 2
Y axis one direction = constant activ high on pin 5 and step pulses (activ high)on pin 4
the oter direction = no signal on pin 5 and step pulses (activ high)on pin 4
Z axis one direction = constant activ high on pin 7 and step pulses (activ high )on pin 6
the oter direction = no signal on pin 7 and step pulses (activ high)on pin 6
A axis one direction = constant activ high on pin 9 and step pulses (activ high )on pin 8
the oter direction = no signal on pin 9 and step pulses (activ high)on pin 8
Sorry
Re: Motors resonating
18Good idea this openly setup in Engine Setup panel (Step Low Active on/off). This need change My Controller (H2 PCB) also (use low active Step signal).
www.hobbycnc.hu