Page 1 sur 7

Jeducut with TB6560 4axis cnc board - if possible

Posté : jeu. juin 03, 2010 7:56 pm
par Dan
Hello

I buy a 4axis cnc board controler TB6560 but the LPT signal out is not compatibile with jedi setup.
I make a converter to pins but motors working only to 1 step.
It is possible working the board with jedi.
The board working with dir/step and enable.

Re: Jeducut with TB6560 4axis cnc board - if possible

Posté : jeu. juin 03, 2010 8:30 pm
par Jerome
Hello,

What kind of signal do you need ? If you build a converter, you just have to select the right dll file.

Re: Jeducut with TB6560 4axis cnc board - if possible

Posté : ven. juin 04, 2010 11:56 am
par Dan
Configuration pins of signal on board is:
x dir - pin1
x step - pin16
x enable - pin4
y dir - pin7
y step - pin14
y enable - pin17
z dir - pin6
z step - pin3
z enable - pin5
c dir - pin8
c step - pin9
c enable - pin5
I change to pin spec for Jedi configuration
x,y,z,c but the enable mount all to pin17
Is it possible separate enable to spec, pins?

Re: Jeducut with TB6560 4axis cnc board - if possible

Posté : ven. juin 04, 2010 6:31 pm
par Jerome
Hi !

I think that just one motor run correctly ?

Jedicut control just one "enable" signal. Try to connect pin 4, 17, 5 and the last pin for "enable" signal on your board (there are 2 pin number 5 in your list).

Re: Jeducut with TB6560 4axis cnc board - if possible

Posté : dim. juin 06, 2010 9:56 pm
par Dan
Before I ask You I change the pins at first time:
X,Y,Z,C to specyfic pins corectly by Jedicut program and my enable signal I mount to 17pin with specyfication Jedicut. But motors runing only by one step. Somethimes runing by clic to right but another clic run to left by one step. The working motors is step by step when I click not non-stop.
Maby working by prefered dll files. ?
I ask you because the my method is bad, motors not working.
Maby i forget something?

Re: Jeducut with TB6560 4axis cnc board - if possible

Posté : mar. juin 22, 2010 11:55 pm
par Dan
Hi
Maby not working because my board start with enable=O, do you have a dll files with enable=1 to pin17
I'm using a XP OS.
Dan

Re: Jeducut with TB6560 4axis cnc board - if possible

Posté : mar. juin 22, 2010 11:57 pm
par Dan
Dan Wrote:
-------------------------------------------------------
> Hi
> Maby not working because my board start with
> enable=0, do you have a dll files with enable=0 to
> pin17
> I'm using a XP OS.
> Dan

Re: Jeducut with TB6560 4axis cnc board - if possible

Posté : jeu. sept. 16, 2010 9:31 pm
par 300lbsgorilla
Did you ever figure out how to make this work with this board? I have the same set up. I made a custom cable and everything work great with a different foam cutting software. I want to try this one but I have not had much luck.

Re: Jeducut with TB6560 4axis cnc board - if possible

Posté : ven. sept. 17, 2010 11:31 am
par HCNC
Hello!

See setup and info (this is TB6560AHQ) : H2 PCB CNC Controller

Re: Jeducut with TB6560 4axis cnc board - if possible

Posté : mer. sept. 22, 2010 9:49 am
par Dan
Hello
From what I understand it to work properly with the program jedicut need an additional module or signal generator.
The first question is whether it will work with my board which is different from yours. My board is 4axis based on TB6560HQ bought on ebay.
Second question: after the construction of the module where you connect it to the board, little is written about this on your site.
If you send me additional information to my email address it was grateful.
Dan