Re: Jedicut-Alden-PL
Posté : mar. nov. 03, 2020 8:08 pm
Bonjour Alain
Après une longue attente pour les éléments, j'ai commencé un combat inégal avec l'affichage. Pour l'instant, sur la table sans démarrer les moteurs, j'ai fait un petit bout de chemin en essayant de comprendre la relation entre le programme téléchargé et les valeurs Jedicut affichées sur l'écran LCD.
Je suis intrigué par le fait que les valeurs V1,C1 et V2,C2 stockées sur la carte Chaufe à Jedicut sont affichées différemment sur l'écran LCD. Pour V1, la valeur de C2 est affichée, et pour V2, la valeur de C1 est indiquée sur les photos jointes n° 7,8,9. En outre, pour la sélection (Activer la chauffe) et (Choix d`un matériel), la vitesse de "Vitesse lente" réglée dans (Machine) 2,48 passe à 2,52 et la "Vitesse rapide" réglée à 4,73 passe à 4,88, je ne sais pas si c`est l`effet de la correction de la chauffe ou autre chose que je ne comprends pas. J'envoie quelques photos de mon combat et un schéma des connexions mises à jour pour la CNC V3. Dans le diagramme "Branchement shield V3.pdf", il y a une erreur dans la connexion du potentiomètre et de l'interrupteur, ils doivent être connectés aux broches ABORT (A0) et HOLD (A1) et non à SpnEN (12) et Spn Dir (13). C'est tout ce que j'ai remarqué jusqu'à présent. Je vais continuer à explorer le sujet en augmentant lentement le nombre de modules à connecter.
Hello Alain
After a long wait for the parts, I started an unequal fight against the display. For the time being, on the table without starting the engines, I went a small way trying to understand the relationship between the uploaded program and the Jedicut values displayed on the LCD.
I am puzzled by the fact that the V1,C1 and V2,C2 values stored on the Chaufe card in Jedicut are displayed differently on the LCD. For V1 the value of C2 is displayed and for V2 the value of C1, you can see it on the attached photos no. 7,8,9. Moreover, for the selection (Activer la chauffe) and (Choix d`un materiau) the speed "Vitesse lente" set in (Machine) 2.48 increases to 2.52 and "Vitesse rapide" set to 4.73 increases to 4.88, I don't know if it is the effect of heating correction or something else I don't understand. I am sending some pictures of my struggle and a diagram of updated connections for CNC V3. In the diagram "Branchement shield V3.pdf" there is an error in the connection of the potentiometer and switch, they should be connected to the pins ABORT (A0) and HOLD (A1) and not to SpnEN (12) and Spn Dir (13). This is what I have noticed so far. I will continue to explore the topic by slowly expanding the number of modules to be connected.
Lien vers les photos :
https://1drv.ms/u/s!AsHmXm4zdu3YgQh40GO ... W?e=PITPhs
https://1drv.ms/u/s!AsHmXm4zdu3Ye9W7Lmb ... g?e=UvqVVN
Après une longue attente pour les éléments, j'ai commencé un combat inégal avec l'affichage. Pour l'instant, sur la table sans démarrer les moteurs, j'ai fait un petit bout de chemin en essayant de comprendre la relation entre le programme téléchargé et les valeurs Jedicut affichées sur l'écran LCD.
Je suis intrigué par le fait que les valeurs V1,C1 et V2,C2 stockées sur la carte Chaufe à Jedicut sont affichées différemment sur l'écran LCD. Pour V1, la valeur de C2 est affichée, et pour V2, la valeur de C1 est indiquée sur les photos jointes n° 7,8,9. En outre, pour la sélection (Activer la chauffe) et (Choix d`un matériel), la vitesse de "Vitesse lente" réglée dans (Machine) 2,48 passe à 2,52 et la "Vitesse rapide" réglée à 4,73 passe à 4,88, je ne sais pas si c`est l`effet de la correction de la chauffe ou autre chose que je ne comprends pas. J'envoie quelques photos de mon combat et un schéma des connexions mises à jour pour la CNC V3. Dans le diagramme "Branchement shield V3.pdf", il y a une erreur dans la connexion du potentiomètre et de l'interrupteur, ils doivent être connectés aux broches ABORT (A0) et HOLD (A1) et non à SpnEN (12) et Spn Dir (13). C'est tout ce que j'ai remarqué jusqu'à présent. Je vais continuer à explorer le sujet en augmentant lentement le nombre de modules à connecter.
Hello Alain
After a long wait for the parts, I started an unequal fight against the display. For the time being, on the table without starting the engines, I went a small way trying to understand the relationship between the uploaded program and the Jedicut values displayed on the LCD.
I am puzzled by the fact that the V1,C1 and V2,C2 values stored on the Chaufe card in Jedicut are displayed differently on the LCD. For V1 the value of C2 is displayed and for V2 the value of C1, you can see it on the attached photos no. 7,8,9. Moreover, for the selection (Activer la chauffe) and (Choix d`un materiau) the speed "Vitesse lente" set in (Machine) 2.48 increases to 2.52 and "Vitesse rapide" set to 4.73 increases to 4.88, I don't know if it is the effect of heating correction or something else I don't understand. I am sending some pictures of my struggle and a diagram of updated connections for CNC V3. In the diagram "Branchement shield V3.pdf" there is an error in the connection of the potentiometer and switch, they should be connected to the pins ABORT (A0) and HOLD (A1) and not to SpnEN (12) and Spn Dir (13). This is what I have noticed so far. I will continue to explore the topic by slowly expanding the number of modules to be connected.
Lien vers les photos :
https://1drv.ms/u/s!AsHmXm4zdu3YgQh40GO ... W?e=PITPhs
https://1drv.ms/u/s!AsHmXm4zdu3Ye9W7Lmb ... g?e=UvqVVN