Hello
I buy a 4axis cnc board controler TB6560 but the LPT signal out is not compatibile with jedi setup.
I make a converter to pins but motors working only to 1 step.
It is possible working the board with jedi.
The board working with dir/step and enable.
Re: Jeducut with TB6560 4axis cnc board - if possible
2Hello,
What kind of signal do you need ? If you build a converter, you just have to select the right dll file.
What kind of signal do you need ? If you build a converter, you just have to select the right dll file.
Jerome
Re: Jeducut with TB6560 4axis cnc board - if possible
3Configuration pins of signal on board is:
x dir - pin1
x step - pin16
x enable - pin4
y dir - pin7
y step - pin14
y enable - pin17
z dir - pin6
z step - pin3
z enable - pin5
c dir - pin8
c step - pin9
c enable - pin5
I change to pin spec for Jedi configuration
x,y,z,c but the enable mount all to pin17
Is it possible separate enable to spec, pins?
x dir - pin1
x step - pin16
x enable - pin4
y dir - pin7
y step - pin14
y enable - pin17
z dir - pin6
z step - pin3
z enable - pin5
c dir - pin8
c step - pin9
c enable - pin5
I change to pin spec for Jedi configuration
x,y,z,c but the enable mount all to pin17
Is it possible separate enable to spec, pins?
Re: Jeducut with TB6560 4axis cnc board - if possible
4Hi !
I think that just one motor run correctly ?
Jedicut control just one "enable" signal. Try to connect pin 4, 17, 5 and the last pin for "enable" signal on your board (there are 2 pin number 5 in your list).
I think that just one motor run correctly ?
Jedicut control just one "enable" signal. Try to connect pin 4, 17, 5 and the last pin for "enable" signal on your board (there are 2 pin number 5 in your list).
Jerome
Re: Jeducut with TB6560 4axis cnc board - if possible
5Before I ask You I change the pins at first time:
X,Y,Z,C to specyfic pins corectly by Jedicut program and my enable signal I mount to 17pin with specyfication Jedicut. But motors runing only by one step. Somethimes runing by clic to right but another clic run to left by one step. The working motors is step by step when I click not non-stop.
Maby working by prefered dll files. ?
I ask you because the my method is bad, motors not working.
Maby i forget something?
X,Y,Z,C to specyfic pins corectly by Jedicut program and my enable signal I mount to 17pin with specyfication Jedicut. But motors runing only by one step. Somethimes runing by clic to right but another clic run to left by one step. The working motors is step by step when I click not non-stop.
Maby working by prefered dll files. ?
I ask you because the my method is bad, motors not working.
Maby i forget something?
Re: Jeducut with TB6560 4axis cnc board - if possible
6Hi
Maby not working because my board start with enable=O, do you have a dll files with enable=1 to pin17
I'm using a XP OS.
Dan
Maby not working because my board start with enable=O, do you have a dll files with enable=1 to pin17
I'm using a XP OS.
Dan
Re: Jeducut with TB6560 4axis cnc board - if possible
7Dan Wrote:
-------------------------------------------------------
> Hi
> Maby not working because my board start with
> enable=0, do you have a dll files with enable=0 to
> pin17
> I'm using a XP OS.
> Dan
-------------------------------------------------------
> Hi
> Maby not working because my board start with
> enable=0, do you have a dll files with enable=0 to
> pin17
> I'm using a XP OS.
> Dan
Re: Jeducut with TB6560 4axis cnc board - if possible
8Did you ever figure out how to make this work with this board? I have the same set up. I made a custom cable and everything work great with a different foam cutting software. I want to try this one but I have not had much luck.
Re: Jeducut with TB6560 4axis cnc board - if possible
10Hello
From what I understand it to work properly with the program jedicut need an additional module or signal generator.
The first question is whether it will work with my board which is different from yours. My board is 4axis based on TB6560HQ bought on ebay.
Second question: after the construction of the module where you connect it to the board, little is written about this on your site.
If you send me additional information to my email address it was grateful.
Dan
From what I understand it to work properly with the program jedicut need an additional module or signal generator.
The first question is whether it will work with my board which is different from yours. My board is 4axis based on TB6560HQ bought on ebay.
Second question: after the construction of the module where you connect it to the board, little is written about this on your site.
If you send me additional information to my email address it was grateful.
Dan